These are the most frequently asked questions! If you have any further questions please email firstname.lastname@example.org
A: A Bunded Oil Tank simply consists of a tank within a tank. The fuel is stored in the inner tank and the outer tank acts as a failsafe so that in the event of a spillage, excess fuel will collect in the bund. They are a requirement at commercial, industrial and institutional premises.
A: The Control of Pollution (Oil Storage) (England) Regulations 2001, are available from the government website Oil storage regulations.
If you have any site-specific queries, feel free to call or email our OFTEC qualified engineers.
A: For domestic premises, you need to carry out an oil storage risk assessment available from OFTEC form TI/133D. All non-domestic oil storage tanks over 200 litres need to be bunded.
A Bund is required if…
A: OFTEC is Oil Firing Technical Association for the Petroleum Industry. It was launched in April 1991 to construct a framework within which oil firing in the United Kingdom and the Republic of Ireland could operate with a greater degree of technical expertise and efficiency. One of its first priorities was to set up a system of training and registration for Technicians engaged in commissioning, servicing, installation and plant operation with oil firing equipment. The scope of the scheme has since been extended to cover Technicians engaged in oil delivery.
A: OFTEC publish ‘Easy Guides” which can be downloaded from their website or a direct link here
Tanks are required to comply with fire separation distances in order to adequately protect the stored fuel from a fire or heat source, which may originate nearby. Tanks should be sited:
if this is not possible then a fire rated barrier with at least 30 minutes protection should be provided 300mm higher and wider than each applicable face of the tank.
A: Oil tanks need to be installed by a competent person, if you do not use an OFTEC registered installer, you will have to contact your local building control.
A: Internal oil storage tanks should never be installed in a habitable area, and should always be contained within an enclosed chamber.
Detailed requirements exist for the installation of oil storage tanks within habitable buildings and domestic garages. For more information, contact OFTEC.
A: An oil loop is a deaerator that helps remove any air or gas bubbles from the oil pipe. Most frequently required when the oil tank is lower than the burner unit or when using a top outlet tank, please note that the oil burner pump must be able to be configured to use a two pipe system to work with the oil loop. Consult an OFTEC engineer for more information.
A: building regulations require a remote acting fire valve as a safety device. The purpose of the valve is to monitor the temperature of the appliance and isolate the oil supply in the event of a fire or significant rise in temperature due to a fault.
A: Contact an OFTEC engineer. Our procedure is to draw off as much water as possible from the bottom of the tank using a vacuum pump, we dip the oil tank with a water detection paste to test if we’ve removed it all. We then add a product called ‘Fuel Set” which will emulsify small amounts of water into the oil and allow it to burn off harmlessly. After that, any filters will be cleaned or changed and the supply pipe is cleared. Bleed the air out of the supply pipe and fire the appliance.
A: You need to use a UN approved container often referred to as an IBC (Intermediate Bulk Container) and depending on the quantity of diesel, you will need to display orange plates and have certain safety equipment. For more information contact us and ask for our leaflet ‘Diesel Fuel, You and the Law”
A: AdBlue is the registered trademark for AUS32 (Aqueous Urea Solution 32.5%) and is used in a process called selective catalytic reduction (SCR) to reduce emissions of oxides of nitrogen from the exhaust of diesel-engined motor vehicles.
AdBlue is carried onboard SCR-equipped vehicles in specially designed tanks and is dosed into the SCR system at a rate equivalent to 3 to 5% of diesel consumption.
So basically, AdBlue is a liquid chemical injected into the exhaust system of trucks, coaches and large commercial vehicles to help lower toxic exhaust gases.
Adblue requires specific storage tanks and pumps as the chemical composition is quite aggressive towards mild steel and yellow metals. Also, the temperature needs to remain above a certain level to keep the product within the designed specification. Pumps, hose fittings and nozzles are best manufactured from stainless steel or special plastics.
IMPORTANT. Whilst every effort is made to keep this information up to date, Southern Tank Services Ltd cannot be held liable for errors or omissions. Compliance with statutory requirements is the responsibility of the person(s) who install, use and maintain products supplied by Southern Tank Services Ltd. If you have concerns over compliance, you must seek professional advice, contact your local Building Control Officer, your local environmental authority or OFTEC. Southern Tank Services Ltd. advises that oil storage installations should be installed and maintained by an OFTEC Registered Technician. Southern Tank Services Ltd. will not be responsible for installations or product use that does not comply with prevailing statutory requirements.
Sign up to our newsletter to be the first to hear about our latest products, special offers and expert advice.